Product Description
Lab Pro Premium Arduino UNO R3 Kit
Finally, an Arduino R3 Lab kit built for University Courses and Lab Pros
This high-quality Arduino Uno R3 includes a full assortment of components and sensors to supply all the basic needs of any course or DIY project. This kit includes a high quality 830pt breadboard and 9V Alkaline battery with power module to connect and power your lab or project with ease.
Over 60 total components are included as outlined below:
Part Description | Qty/kit | Photo | Part Number | |
UNO R3 Original Chip (Arduino compatible) | 1 | ![]() |
ELDEV-ARD1R3-ATM328-01 | |
1.64FT USB 2.0 A-B Male Printer Cable 0.5m | 1 | ![]() |
ELCAB-U2AM.UBM-1.64F-BL-05 | |
Solderless Premium Breadboard 830pt with two power rails | 1 | ![]() |
BBP-10010-EH | |
9V Alkaline Long-life Battery | 1 | ![]() |
ELPOWER-BAT-9VALK-01 | |
Jumper Wire (assorted lengths 65 pieces) | 1 | ![]() |
WIR-020-02410-EH | |
Male-Female DuPont (Jumper) 20mm Wire x20 | 1 | ![]() |
ELWIRE-MF-20 (1/2) | |
28mm LED 5MM White | 5 | ![]() |
ELLEDWH5mmDif05 | |
28mm LED 5MM Red | 5 | ![]() |
ELLEDRD5mmDif05 | |
28mm LED 5MM Green | 5 | ![]() |
ELLEDGR5mmDif05 | |
28mm LED 5MM Yellow | 5 | ![]() |
ELLEDYL5mmDif05 | |
28mm LED 5MM Blue | 5 | ![]() |
ELLEDBL5mmDif05 | |
5MM 4pin Common Anode Clear RGB Tri-Color Red Green Blue LED Diodes | 1 | ![]() |
ELLED-RGB-5mm-CL-CA-05 | |
Carbon Film Resistors 1% 1/4W | ||||
Values: 10R, 100R, 330R, 1K, 2K, 5.2K, 10K, 100K, 1M x 10; 220R x 30 | 120 | ![]() |
ELRES-CF1/4W-1%-120Pack-05 | |
Resistor Values Guide | 1 | ELACC-RESVALUECARD-01 | ||
Sensors | ||||
Sound Sensor Module | 1 | ![]() |
ELSENS-SOUND-05 | |
RTC Module - Real Time Clock (DS3231) | 1 | ![]() |
ELSENS-RTC-05 | |
DHT11 Temp and Humidity Module | 1 | ![]() |
ELSENS-DHT11TEMP-05 | |
HC-SR501 PIR Motion | 1 | ![]() |
ELSENS-HC-SR501-05 | |
HC-SR04 Ultrasonic Module Distance Sensor | 1 | ![]() |
ELSENS-HC-SR04-05 | |
Water Level Detection Sensor Module | 1 | ![]() |
ELSENS-WATERLVL-05 | |
GY-521 Module, pre-soldered | 1 | ![]() |
ELSENS-GY521-PS-05 | |
MFRC-522 RC522 RFID + S50 Card + Keychain, (pre-soldered) | 1 | ![]() |
ELSENS-RFID-MFRC522-PS-05 | |
Tilt Ball Switch (Vibration Sensor) | 1 | ![]() |
ELSW-TILT-05 | |
ICs | ||||
L293D - Quadruple Half-H Drivers 4.5 to 36V 600mA PDIP-16 | 1 | ![]() |
ELIC-L293D-05 | |
74HC595 - 8-bit shift register with 3-state output registers PDIP-16 | 1 | ![]() |
ELIC-74HC595-05 | |
555 Timer/Oscillator (Single Precision Timer) PDIP-8 | 1 | ![]() |
ELIC-LM555-05 | |
UA741 - General Purpose Operational Amplifier PDIP-8 | 1 | ![]() |
ELIC-UA741CN-05 | |
Capacitors | ||||
22pF Ceramic Capacitor | 5 | ![]() |
ELCAP-CD-50V-22P-05 | |
100K pF or .01uF (104) Ceramic Capacitor | 5 | ![]() |
ELCAP-CD-50V-.01U-05 | |
10uF 50V Elecrolytic Capacitor | 2 | ![]() |
ELCAP-AE-50V-10U-05 | |
100uF 50V Electrolytic Capacitor | 2 | ![]() |
ELCAP-AE-50V-100U-05 | |
5mm 5528 LDR Light Dependent Photo Resistor | 2 | ![]() |
ELSENS-LDR-5528-05 | |
Thermistor (10K) | 1 | ![]() |
ELPOWER-CPT-10K-05 | |
1N4007 Diode Rectifier | 5 | ![]() |
ELSEMI-DIO-1N4007-05 | |
PN2222 NPN Transistor | 5 | ![]() |
ELSEMI-PN2222-NPN-05 | |
S8050 NPN Transistor | 5 | ![]() |
ELSEMI-S8050-NPN-05 | |
Active Buzzer (5V) | 1 | ![]() |
ELSPKR-AB-5V-05 | |
Passive Buzzer (5V) | 1 | ![]() |
ELSPKR-PB-5V-05 | |
Tactile Push Button Switch 6x6x5 | 5 | ![]() |
ELSW-TPB-TH-05 | |
1 digit 7 Segment Display, 0.56 inch Red | 1 | ![]() |
ELLED-7SD1-.56-CC-RD-05 | |
4 Digit 7 Segment LED Display 12pin 0.56 inch Red | 1 | ![]() |
ELLED-7SD4-.56-CC-RD-05 | |
LCD1602 Module (W pin header) | 1 | ![]() |
DIS-010-00015-EH | |
MAX7219 Dot Led 8x8 Matrix Module with cable(Red) | 1 | ![]() |
ELLEDMTX-MAX7219-05 | |
Potentiometer 10K with Top Knob | 2 | ![]() |
3386P-1-103TLF-EL | |
Rotary Encoder Module | 1 | ![]() |
ELSW-REC-KS-01 | |
Servo SG90 9g 180 Degree | 1 | ![]() |
ELMOTOR-SG90-05 | |
28BYJ-48 5V 4-Phase Stepper Step Motor | 1 | ![]() |
ELMOTOR-28BYJ48-4P-05 | |
ULN2003 Stepper Motor Driver Board | 1 | ![]() |
ELMOTOR-DB-ULN2003-05 | |
3-6V Servo Motor w/breadboard pins | 1 | ![]() |
ELMOTOR-DC-3Vto6V-BBPINS-05 | |
Three-leaf Fan attachment | 1 | ![]() |
ELACC-3LFAN-05 | |
Breadboard Power Supply Module (9V) | 1 | ![]() |
ELPOWER-PWS-KS-05 | |
9V 1A Power Supply / Adapter | 1 | ![]() |
ELPOWER-PS-9V1A-05 | |
9V Battery Snap with DC Connector | 1 | ![]() |
ELPOWER-BATSNAP-DC-9V-05 | |
SRD-05VDC-SL-C Power Relay 5pin | 1 | ![]() |
ELPOWER-PR-5VDC-5P-05 | |
IR Remote Control | 1 | ![]() |
ELACC-IRR01-05 | |
1838B IR Receiving Head Remote Control Receiver | 1 | ![]() |
ELACC-IRRCR1838B-05 | |
Joystick Module | 1 | ![]() |
INP-010-00015-EH | |
Membrane Switch Keypad Module (matrix 4x4) | 1 | ![]() |
ELKEYP-4416-05 |
The Eureka Leap’s Lab Pro Premium Arduino UNO R3 kit provides an open-source electronics prototyping platform for university and college students based on flexible, easy-to-use hardware and software.
The Lab Pro Premium Arduino UNO R3 kit parts list includes the components recommended by Arduino for learning to use the UNO R3, as demonstrated in the Arduino Projects Book. This kit leverages learning videos, books, and materials from dozens of quality sources online and in print.
This economical and high-value kit includes over 60 quality components and sensors, including LEDs, resistors, potentiometers, LCD1602, RFID modules, and an 830 tie-point breadboard, which will meet your needs for various projects, whether simple or complex. The components are compatible with Arduino UNO R3 (included), UNO R4, MEGA 2560 R3, or Nano.
SIGNIFICANT UPGRADES:
The Lab Pro Premium Arduino UNO R3 Kit was created for college and university students and has significant upgrades over similar kits for hobbyists:
- An upgraded UNO R3 with the Original Chip vs a cheaper China-made compatible chip.
- An extensively enhanced 830Pt breadboard. The breadboard we include is the best made in the world. This is crucial so students do not fail labs because of a lousy breadboard with poor connections.
- The contacts are Phosphorous Bronze with a Plated Nickel Finish, rated for 50,000 insertions, and provide superior electrical and thermal conductivity, corrosion resistance, and excellent formability.
- Securely fits wire sizes from 16 to 26 AWG, 0.016 to 0.05 inches diameter (0.4 to 1.3mm diameter).
- The GY-521 modules and RFID board connectors are pre-soldered; this can be a significant issue if operating outside of labs with soldering equipment and safety glasses and equipment.
- We include a 555 timer and UA741 IC in addition to L293D and 74HC595, which are popular in many electronic course labs.
- We include an upgraded 10K potentiometer with a top knob (3386P-1-103TLF), which is much easier to use and has better results.
- We use the DS3231 RTC Module instead of the DS1307; this is more accurate as it has an internal temperature-compensated crystal oscillator.
- We add fresh 9V batteries to kits before shipping, not stuck on a shelf for over a year.
FULLY CUSTOMIZABLE:
The Lab Pro Premium Arduino UNO R3 kit can be customized. Eureka Leap will work with you to add, replace, or delete parts so that the kit is exactly what your students need for their labs. Contact sales for details.